Common Mistakes To Avoid When Using An Airbrush Air Compressor

Common Mistakes To Avoid When Using An Airbrush Air Compressor

An air compressor generally makes life easier for you and I consider it to be definitely a must have. Some work is simply tedious and ends up being too time-consuming unless you have an air compressor. Air compressors are not cheap and you, therefore, need to properly take care of it and ensure it always works at the best possible performance. An airbrush compressor is a tool that everyone should have and it is quite simple to use. You need to pick the best airbrush compressor and to do this you need to actually do a little bit of research and look at reviews from different airbrush users. You also need to remember that the price usually dictates the quality of airbrush you are buying. Since an airbrush compressor is supposed to make life simple for you and you spent a fortune on it, you should take time to know all the common mistakes to avoid when using an airbrush air compressor.

Sometimes you might be geared up and ready to start work but your air compressor simple refuses to start. What do you do at this point? This is a very common problem that you are going to experience most of the time. This problem is usually caused by air pressure not being low enough to start the compressor engine. An airbrush compressor with tank usually has a gauge to measure the pressure. In case the reading on your gauge is higher than the pressure required, pull out the stop valve thereby releasing a little bit of pressure. Once you are able to do this then you can start your airbrush compressor with a lot of ease.

2.Don’t Store Your Air Compressor In Low Temperatures

This is true especially during winter which affects mostly oil-lubricated compressors. When your compressor is stored in low temperatures than the oil thickness and may even solidify. In simple English, your engine simply won’t juice up. At this point, if you decide to start your airbrush compressor then your breaker will pop or it just won’t start. Ensure you always store your air compressor in a warm place and if it does get too cold, then you should simply give it some warmth. To do this you simply need to move it over to a heated area and leave it there for around one hour.

3.Air Leakage

Sometimes you may find air not reaching your airbrush. This is usually because there are a few leaks that are actually making air not reach the tools. When you experience this, the first step will be to detach your airbrush from the hose. You then need to leave the airbrush compressor switched on actually allowing it to charge. You then need to carefully and slowly apply to the seals and connections soapy water. You will see bubbles and this is an indication of leakage at that particular point. When you see bubbles you should ensure you secure that particular point properly. Many times you find that the air leakage is caused by cracked pipes or simply damaged components. You could easily buy these parts and replace them, it is a simple do it yourself procedure. If this particular problem becomes too difficult for you to deal with, then it is advisable to seek help from a qualified technician. When it comes to air compressors they may become a little bit technical to handle and you should not shy from getting help from a qualified personnel.

4.Humming Sounds From Your Airbrush Compressor

Your compressor should always start with a motor kick sound but a number of times you might hear a humming sound. You should not be alarmed and I will explain to you what the problem really is. Most likely it is your unloader valve that not working correctly and needs fixing or replacing. When your unloader valve is not working properly then an additional load of air is inside your air compressor and may prevent your motor from starting. To deal with this issue then you have to completely empty your tank. You can therefore easily start your airbrush compressor and you humming sound will be completely gone.

5.Your Airbrush Compressor Slows Down Or Stops From Time To Time

Sometimes you might be using your airbrush compressor and it slows down while you’re working or just stops. This is usually caused by a problem in the power supply and it may not be distributing adequate voltage. The first step to solving this problem is actually to make sure no other devices are connected to the circuit the airbrush compressor is using. You could also try to run your air compressor on a different outlet or you could connect it directly. This will ensure your airbrush compressor does not slow down during the work you are doing.

If you, however, find no signs of electrical faults then it may just be a problem with your oil level or the lubricant coating. Always ensure the oil used is clean and does not have any debris. It should also not have any amber in color. For a typical airbrush compressor, you will definitely need to call a technician to help you fix the problem. Common Mistakes To Avoid When Using An Airbrush Air Compressor

Conclusion

Like I said earlier an airbrush compressor is essential when you want to get work done easier and faster. You are however responsible to ensure you keep it in good condition. Maintenance is key and you should perform it a few times every year to ensure everything is in good shape. Sometimes you may not be sure why your airbrush compressor has a few issues and you should seek advice from a professional. Air compressors can be a little difficult to deal with and you may not completely know what the problem might be. However, it is key to note that airbrush compressors are important and I highly recommend you purchase one today. Do a little bit of research and ensure you find one that is suitable for you and easy to use. Click here to find more compressor..

Mary T. White
 

Hi everyone, I’m a trained AC service technician who uses several tools in my profession. I created this interactive platform to share experiences and vital information. Feel free to share your views and ask any question.

Click Here to Leave a Comment Below 0 comments

Leave a Reply: